Parts & Accessories

- Plastic spoke covers in a variety of colors - 300mm cut to fit length - 36 pieces - enough for one wheel - Increases visibility and demands attention

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)

Replacement Cassette body for Origin8 hubs

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

Ultra-light, bolt-on thru-axles, with a low-profile 6mm head for use on Whisky forks and others. They are also available in some common rear frame sizes. See manufacturer's specifications for fitment questions. - Thread Length: 12mm

Clean and Simple is always best. Leverless design for added security and clearance for when situations get tight. These super tough axles tighten up with a 6mm Allen key. They feature "a get out of jail" 6mm Allen key on the drive side of the axle if you manage to round the non-drive side. Constructed from 7075 Aluminium and made to the manufacturer’s exact specifications.

Replacement axle sets for use with Origin8 FB-2000 hubs Front Axle: - 3/8 x 26 x 135 x 175 Rear Axle: - 3/8 x 26 x 170 x 210

Pawl and spring service kit for all Ritchey wheels and hubs V4 and up.

Authentic service axle and end cap kits for Ritchey wheels and hubs. - Replacement axle for non-boost 2-piece disc hubs - Includes axle and end caps - No tools necessary

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

Converts CenterLock hubs to accept 6-bolt rotors - Available for standard Quick Release as well as Thru-Axle hubs - Extruded alloy collar with CNC shoulder pins and lock ring - Eliminates the need for rotor bolts

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Purchase our Kid Trailer axle for your bike. and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - This axle is specifically designed to fit the 142/148 hub standard Surly MDS or Gnot Boost bikes. - The derailleur end of our axle is internally threaded and will use the bolt from your stock Surly axle. The disc brake side of our axle has an engineered mount for your trailer hitch. That mount has been permanently attached to the axle. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. The threads are M10x1 (metric). - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6mm hex wrench required for installation

Freehub bodies for Zipp Cognition hubs.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

- 14 gauge forged 7075 alloy with CNC finish - Matches Halo and Gusset anodized colors perfectly - Sold in bags of 50 - length: 12mm

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm

SRAM's Rise 60 conversion caps are the ticket for converting your Rise 60 wheels to a different axle type.

- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually

WTP's Helix hub guards are designed to work on The Helixline of hubs, replacing the cones for a perfect fit without having to spread your dropouts. - Includes heat-treated chromoly adaptor to replace hub cone nuts for a perfect fit - Rear Hub guards are compatible with Helix V1 and Helix V2 freecoaster hubs and many other "KHE" style freecoasters on the market

Get rolling again with a replacement freehub body for your Mavic wheels. - Freehub for ITS-4 hubs. Also compatible with TS-2 hubs. - Quick engagement 4 pawl design (pawls sold separately)

Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components